Jeep Wrangler CB Antenna Hood Mount | Right Channel Radios

FREE SHIPPING ON ORDERS $75+
TECHNICAL & INSTALLATION RESOURCES | 30,000+ SATISFIED CUSTOMERS TECHNICAL & INSTALLATION RESOURCES
30,000+ SATISFIED CUSTOMERS

Jeep Wrangler CB Antenna Hood Mount (1997 - 2006)

$19.95

  • Built specifically for the overhanging hood of older Wranglers, this mount offers a clean, professional looking install
  • CheckFree 3 Day Shipping for Orders $75+
  • CheckIncludes Installation Resources
  • CheckHassle-Free Returns

One Right Channel customer told us, “This is the #1 antenna mount for your Wrangler.” We have to agree. If you want a factory looking mount, this stainless steel mount attaches to the front fender lip under the hood on either side of your vehicle. All mounting hardware is hidden once installed, further adding to this mounts custom look.

Model / SKU:Firestik SSJ4A
Recommended for:
Mounting a CB antenna on the hood of 1997 to 2006 Jeep Wranglers. This product also mounts well on Hummer roof racks. Recommended for antennas up to 4' tall. For newer jeeps please see this 2007+ hood mount for Jeeps.
Compatible with:All fiberglass and center-load antennas that use a standard 3/8" x 24 threaded base.
Installation Notes:When mounting the bracket, you'll need to drill two 1/4" holes in the inner fender lip. A 12-gauge, 2" x 3/4" support plate installs on the bottom edge of the fender to strengthen the mount. We supply you with 1/4-20" stainless steel bolts, nuts and washers to secure the bracket to the vehicle. We recommend mounting the bracket at least 8" (20cm) from the rear edge of the fender, where the mount will have more support. All installation hardware will be hidden under the hood.
Mount Location:Hood / Fender
Stud Type:PL-259 (Barrel)
Material:Stainless Steel
Product Includes:Jeep Wrangler hood mount, PL-259 style antenna stud
Antenna and coax sold separately
Warranty:Two years

Firestik CB Antenna Mount: These mounts were designed for Jeep Wrangler models 1997 to 2006. This mount lets you install your antenna on either side of the vehicle. The mount and support bracket are made from 12-gauge (0.109") stainless steel. Once installed, you won't see any mounting holes. All mounting hardware -- also stainless steel -- is hidden under the vehicle's hood. Although these mounts are made for newer Wrangler models, the mounting concept is very basic, and the mounts will likely work on pre-1997 Jeeps as well. Mount includes a standard 3/8" x 24 threaded antenna mounting stud.

If you plan on using your vehicle on severe terrain, you should move the mount forward (i.e., closer to the fender bolt) for added stability. The Jeep fender design leaves a large portion of the fender unsupported near the windshield.

The upper bracket is 2" (51mm) wide and 3" (76mm) long. A slight angle on the inside edge of the bracket follows the angle of the hood line. To mount the bracket, you'll need to drill two 1/4" holes in the inner fender lip. A 12-gauge, 2" x 3/4" support plate installs on the bottom edge of the fender to strengthen the mount. We supply you with 1/4-20" stainless steel bolts, nuts and washers to secure the bracket to the vehicle.

Note: The rear part of the fender on newer Jeeps does not have the support found in earlier models. On these vehicles, we recommend mounting the bracket at least 8" (20cm) in front of the rear edge of the fender, where it has sufficient support. If you mount it too far back, or if the rear part of the fender is not given additional support, the fender will flex from any whipping action of the antenna, depending on antenna size.

Reviews