Free shipping $99+ (excludes antennas)
TECHNICAL & INSTALLATION RESOURCES | 100,000+ SATISFIED CUSTOMERS TECHNICAL & INSTALLATION RESOURCES
100,000+ SATISFIED CUSTOMERS

Jeep Wrangler Hood CB Mounting Kit (1997 - 2006)

$42.95

  • Built specifically for the overhanging hood of older Wranglers, this mount + coax combo offers a clean, professional looking install
  • CheckFree Shipping over $99*
  • CheckIncludes Installation Resources
  • CheckHassle-Free Returns

If you love going on long trail rides in your Wrangler, make sure you’re fully rigged out with our custom mount kit built specifically for 1997-2006 Jeep Wranglers. This stainless steel mount attaches to the front fender lip under the hood on either side of your vehicle. All mounting hardware is hidden once installed, further adding to this mounts custom look. This Firestik Mini-Kit also includes 18’ of quality FireRing CB low-profile and weather-resistant ring connection. Recommended for antennas up to 4’ tall.

Model / SKU:Firestik MK-J4R
Recommended for:
Mounting a CB antenna on the hood of a 1997 to 2006 Jeep Wrangler. Recommended for antennas up to 4' tall. For newer models please see this 2007+ hood mount for Jeeps.
Compatible with:All CB radios, and all fiberglass and center-load antennas that use a standard 3/8" x 24 threaded base.
Installation Notes:Important Note: The PL-259 connector (radio screw-on end) is supplied in this kit but is NOT installed on the coax cable. This allows you to route the cable into the vehicle through a smaller (0.375") hole. After placing the connector on the coax, you'll need to solder the center to the PL connector.

When mounting the bracket, you'll need to drill two 1/4" holes in the inner fender lip. A 12-gauge, 2" x 3/4" support plate installs on the bottom edge of the fender to strengthen the mount. We supply you with 1/4-20" stainless steel bolts, nuts and washers to secure the bracket to the vehicle. All installation hardware will be hidden under the hood.
Mount Location:Hood / Fender
Stud Type:Lug (Ring and Terminal)
Material:Stainless Steel
Product Includes:Jeep Wrangler hood mount
18' of Ring CB coax
Warranty:Two years

Firestik CB Antenna Mount: These mounts were designed for 1997 -2006 Jeep Wrangler models. The mount lets you install your antenna on either side of the vehicle. The mount and support bracket are made from 12-gauge (0.109") stainless steel. Once installed, you won't see any mounting holes. All mounting hardware -- also stainless steel -- is hidden under the vehicle's hood. Although these mounts are made for newer Wrangler models, the mounting concept is very basic, and the mounts will likely work on pre-1997 Jeeps as well. Mount includes a standard 3/8" x 24 threaded antenna mounting stud.

If you plan on using your vehicle on severe terrain, you should move the mount forward (i.e., closer to the fender bolt) for added stability. The Jeep fender design leaves a large portion of the fender unsupported near the windshield.

The upper bracket is 2" (51mm) wide and 3" (76mm) long. A slight angle on the inside edge of the bracket follows the angle of the hood line. To mount the bracket, you'll need to drill two 1/4" holes in the inner fender lip. A 12-gauge, 2" x 3/4" support plate installs on the bottom edge of the fender to strengthen the mount. We supply you with 1/4-20" stainless steel bolts, nuts and washers to secure the bracket to the vehicle.

Note: The rear part of the fender on newer Jeeps does not have the support found in earlier models. On these vehicles, we recommend mounting the bracket at least 8" (20cm) in front of the rear edge of the fender, where it has sufficient support. If you mount it too far back, or if the rear part of the fender is not given additional support, the fender will flex from any whipping action of the antenna, depending on antenna size.

Customer Reviews

Based on 12 reviews
92%
(11)
0%
(0)
0%
(0)
0%
(0)
8%
(1)
R
Richard c.
Great Quality mount

Product as described

D
David F.
TJ Mount

Just installed my CB and antenna on my 2001 TJ Jeep. Easy install and works great. I definitely would recommend this mount.

J
Jim W
Repeat customer

Has always been perfect. I will be back
Thank you!

D
Dennis Anderson
Jeep radio

Awesome service very good quality hard ware and fast shipping

C
Charles C.
Poor

Very disappointed . Way over priced. Two inch stiffener is a joke. I used a 7" and still get too much
viberation. Mounting plate needs stiffing.